IMPORTANT - Change of address
product review overlay image

Product Description

Description

The hi-fi preamplifier is the centre of a stereo system. It manages and forwards all external sources. This is done by switching the signal sources and amplifying or weakening the output signal.

High-Fidelity sound quality without distortion on the preamplifier

Another possible function, the interposition of different filters, has been deliberately avoided in the EDITOR.

The reason for this is that with a high level of the other hi-fi components corresponding to the EDITOR, filter circuits are pointless and could have a negative effect on the sound.

The adjustment to the acoustic conditions of the listening room is only possible to a limited extent with the help of tone controls on the preamplifier. With correspondingly high-quality components and acoustically normal rooms, tone control is more harmful than useful.

Nevertheless, the RESTEK EDITOR does not necessarily have to do without sound controls. The preamplifier offers the option of using the SPLIT function to loop an external device into the signal path for room adaptation.

Nine high-level inputs are also sufficient for demanding and complex hi-fi systems

The EDITOR has nine high level inputs. Four of them are designed as symmetrical inputs with mini-XLR and five as asymmetrical inputs with cinch sockets. Optionally, a cinch input can also be converted as a RIA phono preamplifier input.

The RESTEK EDITOR - a preamplifier with the latest technology

Internally, the EDITOR consists of two separate, fully symmetrical, identical mono preamplifiers, each with two volume controls. So there are a total of eight potentiometers. The inputs are switched via high-quality signal relays. the earth connections of the non-switched input sockets are separated from the device to avoid ground loops.

The input sensitivity of the selected input can be adjusted within a range of ± 6 dB to compensate for volume differences when switching between the individual inputs.

Using the volume control, the signal can be attenuated down to -95 dB or amplified up to +10 dB. The two separately controllable outputs can be leveled against each other in a range of ± 6 dB and, if desired, can also be set synchronously with each other.

The output drivers of the pre-amplifier establish the connection to the power amplifiers or active loudspeakers. The low output resistance of 50 ohms and the maximum current of up to 200 mA rms of these driver stages enables correct line adaptation on the one hand and the use of sometimes unavoidably long connecting cables between the preamplifier and the power amplifiers without the music signal being impaired by the cables.

All parts of the electronics of the EDITOR are DC-coupled, making it possible to transmit even the lowest frequencies. This means that even in the lower frequency spectrum, transmission is distortion-free and phase-locked.

There are no capacitors or electrolytic capacitors in the signal path that could cause corruption. Noise and crosstalk can only be detected at the measuring limit.

The claim to ease of use and great functionality is realized through the ability to operate all special functions using the remote control or a single button.

The design of the preamplifier remains puristically clear, since the sophisticated and at the same time impressive concept of one-button operation does not require any further buttons, buttons, controls or the like.

  • Infrared Remote control system
  • Dimmable multifunction display
  • Menu-driven operation of a button
  • Dual mono construction
  • Symmetric and symmetric signal processing volume control
  • Balanced and unbalanced inputs and outputs
  • Adjustable input sensitivity and output level
  • Nine-level inputs, adaptable, RIAA preamp
  • TapeCopy, monitor output, split operation
  • Home Theatre / AV Bypass Function
  • German manufacturing
  • Frequency range: 0 Hz ... 230 kHz (-3dB)
  • Distortion: <0.0005%
  • Signal to noise ratio:> 106 dBA relative to 2 V rms nominal output voltage
  • Crosstalk:> 106 dB referred to 2 V rms nominal output voltage
  • Input Impedance: 47 ohms unbalanced, 10 ohms balanced
  • Input and output level: 10 V rms max.
  • Output current: 200 mA rms max.
  • Output Impedance: 50 ohms
  • Dimensions (WxHxD): 483 x 90 x 365 mm
  • Weight: 10 kg

Specifications

Product Type
Preamplifier
Brand
Restek
Condition
New
Product Code
RESEDITOR

Delivery Information

Delivery is free for all orders over £250.

'In Stock' items ordered before 1pm will be dispatched the same day.

We use DPD Local 'Next Day Service' for most UK deliveries. Orders sent via 'DPD Local - Next Day Service' will be fully tracked with a 1-hour delivery timeslot on the day of delivery. Standard delivery is Monday to Friday.

Saturday delivery can be selected at checkout for £19.95.

Small items and LP's may be sent using Royal Mail.

Large/heavy items may be sent using TNT Express.

For all other countries please visit the 'Delivery Information' link in the footer.

Occasionally, due to stock demand, we can sell out. If this occurs when you make a purchase, we will inform you quickly. Most out of stock items are available for dispatch within 3 working days. If your purchase is urgent, please contact us to check availability.

Customer Reviews

Restek EDITOR Preamplifier

Available

Product Code RESEDITOR

Price Promise: If you find an identical item cheaper from one of our online competitors, tell us and not only will we match the price, we'll beat it by 10% of the difference! Terms and conditions apply, see more information about our price promise.

Customer Reviews